180010
Wrist Pin Remover & Installer
Use on All Models (includingTC88)
This tool is designed to remove and install the piston wrist pin in a one-man operation. No need to drift the pin out.
PRODUCT IN STOCK
$64.50
300010
.105 Check Pins for Cam/Pinion Gears
54-89 Big Twins, Single Cam Models
Used to check Cam and Pinion Gear Diameters for Proper Alignment
910000
PRODUCT IN STOCK
$13.50
300020
.108 Check Pins for Cam/Pinion Gears
90-Up Big Twins, Single Cam Models
Used to check Cam and Pinion Gear Diameters for Proper Alignment
PRODUCT IN STOCK
$13.50
320050
Inner Cam Bearing Puller
86-Pres Big Twins, Single Cam Models
Designed to remove the inner cam bearing perfectly straight from the engine case
PRODUCT IN STOCK
$89.50
320060
Inner Cam Bearing Installer
86-Pres Big Twins, Single Cam Models
Designed to install the inner cam bearing perfectly straight to the proper depth in the engine case
PRODUCT IN STOCK
$77.00
320070
Inner Cam Bearing Tool
58-Pres Big Twin, Single Cam Models
Use to install the inner cam bearing with driver handle 660070 to the proper depth
PRODUCT IN STOCK
$35.00
340010
Pinion Nut Socket
1954-1992 Big Twins
Designed to remove and install the nut holding the pinion gear, Use with a 1/2" drive ratchet or torque wrench
PRODUCT IN STOCK
$25.00
340020
Pinion Gear Remover & Installer
1939-1990 Big Twins
Designed to remove and install the engine pinion gear with ease
PRODUCT IN STOCK
$159.25
340030
Tappet Block Alignment Screws
1979-Present Big Twins
Designed to align tappet blocks for perfect alignment of lifter rollers to camshaft. )Same as 320530 Oil Pump Alignment Screws)
PRODUCT IN STOCK
$17.50
340040
Wrist Pin Bushing Remover/Installer
All Big Twins & Sportsters thru 1999
Designed to remove and install the wrist pin bushings without removing the rods from the engine case
PRODUCT IN STOCK
$64.50
340050
Push-Rod Clip Installation Tool
Use on All Models with push-rod clips
Designed to install the push-rod clip while compressing the center spring at the same time
PRODUCT IN STOCK
$29.95
340060
Pinion Gear Locking Tool
1954-Present Single Cam Models
Designed to lock the pinion gear allowing removal or installation of the pinion gear holding nut
PRODUCT IN STOCK
$71.50
340070
Exhaust Stud Drill Jig
84-Pres BT, 83-08 XL, 87-Pres Buell exc 1125R
Use this jig to drill out broken exhaust studs. Drill bushing allows a straight alignment for removal. Supplied with drill bit
PRODUCT IN STOCK
$59.00
500010
Sprocket Shaft Seal Installer
69-Pres Big Twin Single Cam Models
Designed to install the sprocket shaft engine seal perfectly straight. Use with (500040)
PRODUCT IN STOCK
$51.50
500020
Sprocket Shaft Bearing Race Tool
1969-2002 Big Twins
Use to remove or install the sprocket shaft bearing race in the left side engine case. Use with Driver Handle (660070)
PRODUCT IN STOCK
$36.50
500040
Sprocket Shaft Bearing Installer
1955-Pres Big Twin Single Cam Models
Designed to in the Timken® bearings onto the crankshaft assembly and into the engine case
PRODUCT IN STOCK
$95.50
Inner Cam Bearing (Torrington B138)
58-99 Big Twins, Single Cam only
The only bearing with a full set of rollers to use in your motor (Sold each)
PRODUCT IN STOCK
$7.95
320020
Wrist Pin Cir-Clip Remover & Installer
Use on Shovelhead, Evo & Sportsters
Designed to remove & install the cir-clip from the piston. Works on pistons with retaining ring dimple. Not for use on forged pistons
PRODUCT IN STOCK
$106.95