PRODUCT IN STOCK
$108.00
320670
Crankcase Bearing Remover & Installer
03-Pres Alpha & Beta Engines
Use on 03-Pres Alpha Engines, Pinion & Sprocket Side. 03-Pres Beta Engines Sprocket Side
PRODUCT IN STOCK
$122.95
WRIST PIN CLIP REMOVER & INSTALLER
99-06 Twin Cams, Exc 06 Dyna
Designed to remove & install the cir-clip from the piston. Works on pistons with retaining ring dimple. Not for use on forged pistons.
HD-42317-A
OUT OF STOCK
$298.95
320500
CAM TENSIONER UNLOADER
99-06 TC88, Except 06 Dyna
Use to unload pressure on the primary & secondary chain tensioners. 1-1/4" Hex can be used with standard socket & ratchet
HD-42313
PRODUCT IN STOCK
$34.95
320510
CAMSHAFT REMOVER & INSTALLER
99-06 TC88, Except 06 Dyna
Use to remove & install the camshafts and the ball bearings in the support plate. Ensures a straight, smooth press in & out
HD-43644
PRODUCT IN STOCK
$104.95
320520
CAM/PINION GEAR LOCKING TOOL
99-06 TC88, Except 06 Dyna
Designed to lock the cam & pinion gears to properly remove, install and torque the holding bolts
HD-42314
PRODUCT IN STOCK
$31.95
320530
OIL PUMP ALIGNMENT SCREWS, PAIR
99-Present Twin Cam Models
Designed to align the oil pump to support plate. A must for proper alignment of the gears & oil pressure
PRODUCT IN STOCK
$17.50
320540
INNER CAM BEARING PULLER
99-06 TC88, Except 06 Dyna
Designed to pull the inner cam bearings perfectly straight and prevent the needles from falling into the engine case
PRODUCT IN STOCK
$85.25
320550
INNER CAM BEARING INSTALLER
99-06 TC88, Except 06 Dyna
Designed to install the inner cam bearings perfectly straight to the proper depth
(Cam bearings at bottom of page)
PRODUCT IN STOCK
$82.25
320560
CAMSHAFT BEARING PULLER
1999-2006 TC88, Except 06 Dyna
Designed to remove the camshaft roller bearing with ease after camshafts are removed from the support plate
PRODUCT IN STOCK
$115.50
320570
Wrist Pin Bushing Remover & Installer
99-06 TC88, Except 06 Dyna
Designed to remove and install the wrist pin bushing without removing the rod from the engine case
PRODUCT IN STOCK
$64.50
320580
CAM RELIEF TOOL, SINGLE SPINDLE
99-06 TC88, Except 06 Dyna
This precision tool is designed to relieve the engine cam chest for high-lift camshafts (Pilot for 06-Up on next page 320660)
PRODUCT IN STOCK
$137.25
320590
CAM RELIEF TOOL, DUAL SPINDLE
99-06 TC88, Except 06 Dyna
This precision tool is designed to relieve the engine cam chest for high-lift camshafts (Pilot for 06-Up on next page 320660)
PRODUCT IN STOCK
$220.00
500010
SPROCKET SHAFT SEAL INSTALLER
1999-Pres Big Twins
Designed to install the engine sprocket shaft case seal. Use with (500040) Sprocket Shaft Bearing Installation Tool
PRODUCT IN STOCK
$51.50
500040
Sprocket Shaft Bearing Installation Tool
1955-2002 TC88
Designed to install the Timken bearings onto the crankshaft assembly and into the engine cases. Use with (500010) Sprocket Shaft Bearing Tool
PRODUCT IN STOCK
$95.50
340050
PUSHROD CLIP INSTALLER
All Models
Used to install the pushrod clip by prying down on the center spring cup and sliding the clip into place at the same time
PRODUCT IN STOCK
$29.95
910002
Inner Cam Bearings (Koyo/Torrington B-148)
99-06 Twin Cams, Except 06 Dyna
The only bearings with a full set of rollers to use in your motor. Don't take any chances with any other bearing. (Sold as a Pair)
PRODUCT IN STOCK
$14.95
320490
PINION BEARING REMOVER & INSTALLER
99-02 Alpha Engine Models
Designed to remove & install the right side crankcase bearing perfectly straight with no damage to the engine case
PRODUCT IN STOCK
$109.50
500020
Sprocket Shaft Bearing Race Tool
1969-2002 Big Twins
Use to remove & install the sprocket shaft bearing race in the left side engine case. Use with Driver Handle (660070) & Spacer (660060) located on the Chassis Page
PRODUCT IN STOCK
$42.95
340070
EXHAUST STUD DRILL JIG
84-Pres Big Twins, 83-08 XL, 87-Pres Buell, Exc 1125R
Use this jig to drill out broken exhaust studs. Drill bushing allows straight alignment for removal. Supplied with drill bit
PRODUCT IN STOCK
$66.50
320420
320400
TORQUE PLATES
99-Pres Twin Cam Models
Use these plates to check cylinder run-out, honing and boring cylinders. A must for engine work.
Range 3.750 thru 3.938
320410
TORQUE PLATES
99-Pres Twin Cam Models
Use these plates to check cylinder run-out, honing and boring cylinders. A must for engine work.
Range 4.00" to 4.060"
PRODUCT IN STOCK
$298.95